تزويدك بحل احترافي

غشاء التناضح العكسي للمياه قليلة الملوحة 4040 (ULP31-4040) | ضغط منخفض، رفض 99.5%

  • الموديل: ULP31-4040 – Brackish Water 4040 RO Membrane
  • Low-pressure, high rejection: designed for 4″ vessels with easy retrofit
  • Typical rejection: up to ~99.5% (NaCl, 25 °C, 2,000 ppm, 15% recovery)
  • Energy friendly: lower ΔP at design flux → reduced kWh/m³
  • Quality assurance: each element wet-tested; traceable serial No.

وصف المنتج

ULP31-4040 Brackish Water RO Membrane

إن 4040 brackish water RO membrane (ULP31-4040) is a low-pressure, high-rejection element for groundwater, well water, and industrial reuse applications. It fits standard 4″ pressure vessels and helps reduce operating pressure while meeting product conductivity targets. Each element is individually tested and serialized for traceability.

Where it excels

  • Energy savings: achieve design flux at lower pressure compared with conventional 4040 elements.
  • Stable product quality: high salt rejection reduces polishing load downstream.
  • Easy retrofit: standard 1/2″ permeate tube, common interconnectors, and 4″ vessel compatibility.

Commissioning & acceptance (best practice)

  1. Normalize permeate flow to temperature; compare with clean baseline values.
  2. Verify product conductivity / salt rejection meets design spec at the target recovery.
  3. Confirm stage ΔP is stable after air purge and full wet-out.
  4. Record pressure (feed/concentrate/permeate), flow, and conductivity as your new baseline.

Note: Typical values below are for engineering guidance only. Always confirm with the latest datasheet and your feedwater analysis.

Related guides: RO membrane replacement · Cleaning & CIP · Troubleshooting

معلمة المنتج

Item ULP31-4040 (typical) Test / Notes
Permeate flow ≈ 2,400 GPD (≈ 9.1 m³/d) 2,000 ppm NaCl, 25 °C, 150 psi (1.03 MPa), 15% recovery
Salt rejection up to ~99.5% (typ.) Based on NaCl; field results depend on recovery and temperature
Membrane type Thin-film composite (TFC) Dechlorination required before TFC
Element size 4.0″ × 40″ Standard 4″ vessel; verify brine seal orientation
Permeate tube (ID) ≈ 0.75″ Standard interconnectors
Operating pressure Typically 70–200 psi (0.5–1.4 MPa) Operate within supplier window for the target flux
Max feed temperature 45 °C (113 °F) Correct to 25 °C for normalized data
Allowable pH (continuous) 2–11 Cleaning pH up to 1–12 (short-term) as per supplier
Free chlorine tolerance 0 mg/L (TFC) Dechlorinate upstream; monitor ORP
Recommended SDI < 5 (SDI15) Keep iron/manganese within limits; antiscalant as required

Values are typical and not guaranteed; design and acceptance should follow the latest model datasheet and site water analysis.

الصناعة المطبقة

  • Electronics & component rinsing (BWRO)
  • Bottling / beverage make-up water
  • Laboratories and pilot plants
  • Hotel, clinic, and commercial water supply
  • Well water and groundwater polishing before DI/EDI

الميزة الأولى

Advantage 1 — Low Pressure, High Rejection

ULP31-4040 achieves design flux at lower ΔP while delivering high NaCl rejection. Plants typically see reduced specific energy (kWh/m³) and steadier product conductivity, especially at moderate recovery.

الميزة الثانية

Advantage 2 — Easy Retrofit & Simple Maintenance

Standard 4″ vessel compatibility, common interconnectors, and a 0.75″ permeate tube make changeout straightforward. Baseline acceptance is quick: verify normalized flow, product conductivity, and stage ΔP after wet-out.

المنتجات ذات الصلة

الأسئلة الشائعة

يعتمد عمر نظام التناضح العكسي على جودة المياه والصيانة. عادةً ما يدوم الغشاء من 2-3 سنوات، بينما يمكن أن يدوم النظام نفسه لأكثر من 10 سنوات مع العناية المناسبة.

نعم، جميع أنظمتنا قابلة للتخصيص بالكامل. نقوم بتحليل تقرير المياه الخاص بك واحتياجات التطبيق قبل تقديم حلول مصممة خصيصًا.

تتوافق منتجاتنا مع معايير CE وISO 9001، ويمكن تصميمها لتلبية لوائح إقليمية أو معايير صناعية محددة عند الطلب.

يتم شحن الأنظمة القياسية في غضون 7-15 يومًا. بالنسبة للطلبات المخصصة، قد تمتد المهلة الزمنية إلى 20-25 يومًا حسب درجة التعقيد.

نعم. نحن نقدم وثائق فنية كاملة، وإرشادات عن بُعد عبر الفيديو، ويمكننا إرسال مهندسين دوليًا عند الطلب.

يشمل عرض أسعارنا نظام التناضح العكسي الكامل، ولوحة التحكم، والمضخات، ووحدات المعالجة المسبقة، وجميع التجهيزات اللازمة. ويمكن تضمين أدوات التركيب وقطع الغيار عند الطلب.

المنتجات المفضلة
انتقل إلى الأعلى